Posterior Screws - With direct vertebral body derotation

The aims of surgery are to:

• improve the spinal curve
• improve the three dimensional alignment of the spine
• prevent progression of the curve in the future
• improve cosmesis
• reduce pain
• optimize pulmonary function
• maintain neurological integrity

This is achieved by correction of the deformity and creation of a solid arthrodesis of the deformed part of the spine.

To illustrate this procedure, we will use a left PTC and a right thoracic curve.

Details on selection of fusion levels can be found here.

The procedure is performed through a posterior approach with the patient in the prone position. The lengths of the incision will depend on the levels being fused.

Pedicle screw density would depend on surgeon's preference and preoperative planning. Typically less screws are utilized on smaller and more flexible curves, while more screws are utilized on larger and stiffer curves up to a maximum of segmental screws bilaterally.

Details on pedicle screw insertion.

Depending on flexibility findings, the release can be carried out only at the apex of the curve, which is usually the stiffest, or the whole length of the instrumented spine.

A release is generally performed if the spine cannot easily align to the rod during surgery. This can be predicted preoperatively based on the bending X-ray. For stiff curves, fulcrum bending X-ray and the traction X-ray under general anaesthesia is the method of choice for determining flexibility.

A soft tissue release can be performed by removal of the interspinous ligaments along with the midline ligamentum flavum of the apical regions of the deformity. If additional release is desired, then formal Posterior Column Osteotomy (PCO) can be performed at the same levels. PCO is also called SPO (Smith-Petersen osteotomy) or Ponte osteotomy. The shaded area to the left outlines the bony resection performed during a PCO.

All posterior releases begin by resecting the inferior aspect of the spinous process, followed by removal of the interspinous ligament utilizing a standard rongeur.

Removal of the 3-5 mm of the inferior aspect of the inferior facet joint is performed at each level of the planned fusion using an osteotome.

The ligamentum flavum is removed with a Kerrison rongeur beginning in the midline and exiting lateral until abutting against the medial aspect of the superior facet. It is important not to penetrate deeply against the dura.

Care should be taken not to tear the dura particularly on the concavity of the curve where the neuro tissues preferentially lie.

A Kerrison rongeur is utilized to remove the most cephalad portion of the superior articular facet exiting out lateral into the neuroforamen. This completes the PCO and is usually repeated at other levels.

Epidural bleeding within the neuroforamen is controlled with hemostatic agents and cottonoid packing.

In cases where a PCO has been performed, the facet joint is already removed and this step ("Facet joint fusion") should be omitted.

The inferior articular facet is removed with an osteotome exposing the articular cartilage of the superior articular facet.

Remove the articular cartilage from the superior articular facet using a gouge or a curette.

Insert pieces of bone graft (autograft, allograft, or bone substitute) into the decorticated facet joint for arthrodesis.

These steps are repeated for all the levels on both sides.

The left rod is bent to the appropriate thoracic kyphosis as preoperatively planned with the appropriate transition into mild lordosis at the thoracolumbar junction as necessary.

The amount of thoracic kyphosis bent into the left rod will be based on:

• curve size
• curve flexibility
• number and purchase of bone anchors
• size and material of the rod utilized

Starting with the most cranial screw the rod is inserted into the convex side of the proximal thoracic curve (PTC) conforming to the convexity of the PTC without being locked.

The rod is rotated 90° degrees, into the appropriate sagittal alignment, engaged, and locked to the 1 or 2 most caudal screws to prevent the rod from rotating back. The other screw heads are unlocked.

At this point compression is applied at the cranial three levels along the convexity of the proximal thoracic curve (PTC) correcting the proximal thoracic curve.

Vertebral screw derotation extenders are applied to the three periapical screw heads on the concavity and convexity.

An apical derotational maneuver is then performed to simultaneously translate the apical vertebrae dorsally and medially to meet the kyphotically contoured concave rod. The screws are then sequentially locked to this rod from the ends to the apex.

Holding the spine in a derotated position, distraction is performed starting at the apex pushing caudal against the lower screws while pushing cranial against the upper screws. After the distraction is performed. Each set screw is locked down to hold the correction.

Coronal benders are applied for fine tuning the correction. Care is taken to prevent bone-screw interface failure by applying an appropriate amount of force.

This maneuver is best performed on either stainless steel or cobalt chrome rods and may not be suitable on titanium rods.

The right rod is bent to the appropriate thoracic kyphosis with the appropriate transition into the thoraco lumbar junction as necessary.

The rod is attached to the most cranial screw, in its normal sagittal plane rotation and locked.

After locking the apical screw to the rod, the convex screws are compressed towards the apical anchor to horizontalize each vertebra and then locked in position.

It is recommended to obtain radiographic imaging in both planes to confirm optimal alignment at this point.

Compression (1) or distraction (2) is used at the cranial 2-3 levels in order to fine tune shoulder balance, and at the caudal 2-3 levels in order to optimize LIV position.

The laminae and the transverse processes are decorticated with an osteotome.

Care should be taken to always point the osteotome away from the spinal canal.

Alternatively, the decortication may be performed with a powered burr.

Bone graft (allograft, autograft, or bone substitutes) is copiously placed over the entire decorticated area.

Transverse connectors are optional in this technique based on overall construct stability.

At some point prior to wound closure intraoperative imaging should check:

• Fusion levels
• Screw position
• Overall coronal and sagittal correction and alignment

Intravenous antibiotics are administrated for at least 24 hours, depending on hospital protocol. The use of an epidural pain catheter vs. intravenous patient controlled analgesia (PCA) are utilized for acute pain management.

Early mobilization out of bed, is preferably started the day after surgery. Generally a postoperative brace/orthosis is not required.

It is appropriate to obtain upright PA and Lateral xrays of the patient at some point early postoperative either before the patient is discharged from the hospital or at the 1st postoperative visit as an outpatient

To allow the bone to heal and form a solid arthrodesis, some restriction of sports activities, especially contact sports, is usually advised for 6 months.

Early postoperative complications include:

• Postoperative wound infection
• Urinary tract infection
• Respiratory complications such as pneumonia

Late postoperative complications include:

• Pseudarthrosis with loss of correction
• Late deep wound infections
• "Adding on" which is progression of scoliotic deformity in the non-instrumented spine.
• Crankshaft phenomenon (progression of scoliotic deformity within the instrumented spine).
• Implant failure or other implant related complications

In the long term adjacent segment degenerations above and below the instrumented spine may occur.