1. Home
  2. Skeleton
  3. Diagnosis
  4. Indications
  5. Treatment

Authors of section

Executive editor

Michael Baumgaertner

Authors

Michael Huo, Michael Leslie, Iain McFadyen

Open all credits

Distal femoral replacement

1. Introduction

The distal femoral replacement prosthesis is indicated when there is either insufficient bone stock or poor bone quality.

The tibial component requires revision to be compatible with the new distal femoral replacement.

Distal femoral replacement prosthesis

2. Preoperative planning

Templating

Templating is performed to determine the appropriate length of the distal femoral bone resection.

Length of hinged femoral component

The minimum length of the distal femoral replacement prosthesis is generally in the range of 60-70 mm in most implant systems.

The minimum length of the distal femoral replacement prosthesis is 60-70 mm

Additional intercalary segments are available to meet the reconstructive requirements.

Additional intercalary segments

Femoral stem

The minimum length of the stem for the distal femoral replacement prosthesis is typically 100-125 mm.

Femoral stem

3. Patient preparation

The patient is placed in the supine position. A radiolucent table may facilitate intraoperative fluoroscopy if required.

Patient in supine position

4. Surgical approach

This procedure requires an adequate visualization of the knee joint. The most commonly used is a midline skin incision followed by a medial parapatellar arthrotomy. A proximal and distal extension may be necessary to achieve sufficient visualization and soft tissue releases.

P450 Proximal tibia replacement

5. Femur

Removal of femoral component

Dissection is carried out around the distal femur using the electric cautery. The collateral ligaments and the posterior joint capsule are detached from the distal femur. Care must be undertaken to avoid injury to the neurovascular structures, and to the extensor mechanism of the knee.

Removal of femoral component

The femoral component is removed with the distal femur fracture fragments.

Additional bone resection may be necessary according to preoperative planning.

Additional bone resection may be necessary according to preoperative planning

Preparation of the femur

The femoral resection level can be evened with a planer to optimize contact with the new prosthesis.

Preparation of the femur

The femoral canal is prepared with reamers of increasing size. The depth of the reaming is determined by the length of the selected stem.

The femoral canal is prepared with reamers of increasing size

The diameter of the stem is determined by the reamer diameter which achieves cortical contact with the diaphyseal bone. One should allow for at least 2 mm of cement mantle around the stem if cement fixation is selected.

The diameter of the stem is determined by the reamer diameter which achieves cortical contact with the diaphyseal bone.

6. Tibia

Tibial revision techniques are described under the treatment: complete tibial revision with hinged knee.

7. Trial

The trial components are assembled, and a trial reduction is performed.

P445 Distal femoral replacement

Leg length equalization techniques include:

  • Matching with the preoperative measurement of the contralateral extremity using a radiopaque ruler.
  • Intraoperative clinical evaluation if both legs have been prepped.
using a radiopaque ruler

Proper rotational alignment of the femoral component is referenced to:

  • Linea aspera
  • Fluoroscopic rotational assessment using the lesser trochanter
  • Patellar tracking during trial reduction

The anterior cortex of the femur is marked as reference for final insertion of the prosthesis.

P445 Distal femoral replacement

Patella tracking is carefully assessed to ensure no instability or impingement throughout the entire range of knee motion.

P445 Distal femoral replacement

8. Components insertion

Bone preparation for cementing

The femoral canal is lavaged and dried.

Cement restrictor

The cement restrictor is inserted into the femoral canal to allow for a 1 cm cement mantle between the stem tip and the restrictor.

Cement restrictor

Cementation

Cement is mixed using standard techniques and is inject into the canal with retrograde filling and pressurization, using a cement gun.

cementation

Insertion of femoral component

The femoral component is seated with rotational alignment to previously made marking during the trial reduction.

Insertion of femoral component

9. Final reduction

The selected polyethylene bearing along with the bushings for the hinged articulation are assembled and coupled together. The knee is reduced.

P445 Distal femoral replacement

If patellar tracking is not ideal, a lateral retinacular release and medial imbrication can be performed.

A lateral retinacular release and medial imbrication can be performed

10. Aftercare

The patient can be mobilized with full weight-bearing and active range of motion immediately after surgery.