Specific considerations for the tibia and the femur are given below.
AO teaching video: Femur--Tibia Articular Fracture Large External Fixator: Knee-bridging Modular Frame
3. Patient preparation
This procedure is normally performed with the patient in a supine position.
4. Pin insertion (tibia/femur)
For safe pin placement make use of the safe zones and be familiar with the anatomy of the lower leg and the femur.
The safe zone for the femur is lateral. In temporary external fixation, the pins should be placed so that they do not interfere with planned later definitive fixation; this may mean placing femoral pins anteriorly or anterolaterally.
In the femur, blunt dissection of the soft tissues and the use of small Langenbeck retractors will minimize muscular damage.
Using a straight clamp, prepare a channel for the insertion of the pin.
Tibial pin placement
Drilling a hole in the thick tibial crest may be associated with excessive heat generation and there is a risk the drill bit may slip medially or laterally damaging the soft tissues. As the anteromedial tibial wall provides adequate thickness for the placement of pins, this trajectory is preferable. A trajectory angle (relative to the sagittal plane) of 20-60° for the proximal fragment and of 30-90° for the distal fragment is recommended.
Alternatively, in order to avoid the frame catching on the opposite leg, the pins may be placed more anteriorly. The drill bit is started with the tip just medial to the anterior crest, and with the drill bit perpendicular to the anteromedial surface (A). As the drill bit starts to penetrate the surface, the drill is gradually moved more anteriorly until the drill bit is in the desired plane (B). This should prevent the tip from sliding down the medial or lateral surface.
5. Frame construction / reduction and fixation (tibia/femur)
Pearl: oblique distal tube Angle the rod over the tibia such that it is attached to the pins one on the lateral and one on the medial side. This results in a larger window over the condyle which can be beneficial for later (minimally invasive) surgery if it is necessary to maintain the external fixator during definitive osteosynthesis.
Reduction and fixation
Restore length with a bolster behind the knee to give slight flexion.
It should be understood that a perfect reduction will not be obtained.
Pitfall: Flexion of the articular block
Care must be taken that the fracture is not too distracted, since the pull of the gastrocnemius muscle would hyperextend the condylar block.
Insufficient distraction leads to insufficient reduction.
6. Aftercare following external fixation
Consideration should be given to thromboembolic prophylaxis, according to local treatment guidelines.
Proper pin insertion To prevent postoperative complications, pin-insertion technique is more important than any pin-care protocol:
Correct placement of pins (see safe zones) avoiding ligaments and tendons, eg tibia anterior
Correct insertion of pins (eg trajectory, depth) avoiding heat necrosis
Extending skin incisions to release soft-tissue tension around the pin insertion (see inspection and treatment of skin incisions)
Pin-site care Various aftercare protocols to prevent pin tract infection have been established by experts worldwide. Therefore no standard protocol for pin-site care can be stated here. Nevertheless, the following points are recommended:
The aftercare should follow the same protocol until removal of the external fixator.
The pin-insertion sites should be kept clean. Any crusts or exudates should be removed. The pins may be cleaned with saline and/or disinfectant solution/alcohol. The frequency of cleaning depends on the circumstances and varies from daily to weekly but should be done in moderation.
No ointments or antibiotic solutions are recommended for routine pin-site care.
Dressings are not usually necessary once wound drainage has ceased.
Pin-insertion sites need not be protected for showering or bathing with clean water.
The patient or the carer should learn and apply the cleaning routine.
Pin loosening or pin tract infection In case of pin loosening or pin tract infection, the following steps need to be taken:
Remove all involved pins and place new pins in a healthy location.
Debride the pin sites in the operating theater, using curettage and irrigation.
Take specimens for a microbiological study to guide appropriate antibiotic treatment if necessary.
Before changing to a definitive internal fixation an infected pin tract needs to heal. Otherwise infection will result.
See patient 7-10 days after surgery for a wound check. X-rays are taken to check the reduction.
The external fixator is usually removed prior to the definitive internal fixation. Occasionally, it may be maintained for aid in reduction of the fracture during plate fixation.