Displaced transcervical and subcapital fractures are unstable. Their prognosis is by and large the same and they will be discussed as one group for the purpose of manner of reduction and choice of fixation, should internal fixation be chosen as the method of treatment. They can be stabilized with either cannulated screws or DHS. At this point we do not have sufficient evidence based information to point to one or the other method as superior. If the surgeon feels that optimal stability is required, he should choose a sliding hip screw (DHS) type of implant for fixation. If added rotational stability is desired in addition to the DHS, a cannulated screw is inserted above and parallel in both planes to the DHS. It must be parallel in order not to block the sliding property of the DHS implant.
Principles of reconstruction
Use two or three 7.0 mm or 7.3 mm cancellous screws. Make sure they are parallel and that the thread is in the head fragment and does not cross the fracture line. The inferior screw should rest on the calcar. A washer may be used to stop the screw head from penetrating the bone of the greater trochanter. These screws can be inserted open or percutaneously through stab incisions.
AO teaching video: The 7.3mm Cannulated Screw: Femoral Neck Fracture
2. Flynn reduction maneuver
The most logical and anatomically based, atraumatic reduction maneuvre for displaced intracapsular fractures of the femoral neck, was published by Flynn (1974). This is not appropriate for the totally displaced intracapsular fractures.
It is based on the fact that in the anatomical position, the major capsular fibres of the hip joint are in a spiral configuration.
This arrangement pulls the femoral head tightly into the acetabulum: Flynn described this as the “tight-packed” status of the hip.
If the hip is flexed and slightly abducted, the spiral of the capsular fibres is unwound...
... producing the “loose-packed” condition of the hip joint.
In the “loose-packed” state, manual traction along line of the femoral neck disimpacts the fracture fragments.
The traction produces an hour-glass shape to the capsule, which realigns the disimpacted fracture fragments.
The most comfortable set-up is for the assistant to support the heel of the injured leg, whilst the surgeon’s ipsilateral hand pulls along the line of the femoral neck, the other hand controlling the knee.
Whilst manual traction is maintained along line of the femoral neck, the leg is first internally rotated, to correct any retroversion, and is then brought down to the extended position.
This produces a “tight-packed” hip and impacts the realigned fracture fragments.
...to allow unimpeded positioning of the image intensifier. The reduction must be checked in both the AP and lateral views with an image intensifier. If closed reduction fails, carry out a limited open reduction.
3. Lateral approach for closed reduction and fixation
The screws must be parallel. The guide wires may be inserted freehand under x-ray control to ensure they are parallel, or an aiming device may be used if available.
If using an aiming device, expose the greater trochanter through an incision just large enough for the device.
If using an aiming device with a central hole, it may be best to start by placing a wire in the center of the neck and head. The three wires for screws may then be placed through the aiming device in a triangle around the central wire, with one wire below and two above the central wire.
Alternatively, the first wire may be placed along the inferior border of the neck, with the two superior wires then being placed parallel to the first wire.
Determine screw length
Determine the length of the screws with the aid of the measuring device. Choose the length of the drill and screws 5 mm shorter than the length of the guide wires.
Insertion of the cannulated screws
Drill over the wires with a 3.6 mm cannulated drill bit. Then insert three 7.0 mm or 7.3 mm cannulated cancellous screws over the wires. In younger patients with dense cancellous bone, the cannulated tap may be necessary to precut the thread. A washer may be used to avoid penetration of the screw head through the thin cortex.
5. Postoperative treatment
Elderly patients tend not to do well if kept immobilized, so early mobilization should be encouraged. Depending on the fracture configuration, strength of the bone and security of fixation, the surgeon may prefer partial or full weight bearing.
In reality, many elderly patients may not be able to comply with instructions for partial weight bearing.
In practice, it is often best overall to allow weight bearing as tolerated.
Prognosis of proximal femur fractures
After surgery the outcomes of greatest concern are:
loss of independence
loss of mobility
Mortality Mortality generally occurs within the first six months after fracture; studies have shown that these rates range from 12-37%.
Predictors of higher mortality rates are patients who are:
have other comorbid conditions (such as cardiac failure, diabetes, and chronic air flow limitation)
have cognitive disorders.
Ability to return home Besides mortality, the ability to return home is also an important outcome for patients with hip fractures. Studies have shown that as few as 50% of patients were able to return home, and that mortality rates are lower in those that do return home compared with rates in those that are transferred to nursing homes or rehabilitation centers.
Predictors of returning home include:
a younger age (less than 85 years)
ability to walk independently preoperatively
ability to perform activities of daily living preoperatively
living with another person
ability to walk independently at the time of discharge from the hospital.