As with any articular injury, anatomical restoration of the joint surface must be obtained. This is generally best done under direct vision, with clamp application, provisional fixation and then lag screw fixation.
The surgeon must bear in mind that the strong axial loading forces, as well as varus/valgus stress in the knee joint can tend to displace fragments. With vertical fracture lines, in particular, screw fixation alone may not be sufficient, and a buttress plate should be added.
In fractures with a vertical fracture line, a buttress plate is necessary to counteract the vertical shear forces. The buttress plate prevents proximal displacement of the fragment.
The buttress plate is added to enhance the stability and to counter axial load on the fracture, especially in osteoporotic bone.
2. Patient preparation
This procedure may be performed with the patient in one of the following positions:
Remove the intraarticular hematoma and rinse the joint thoroughly with Ringer lactate solution.
Reduce the fragment by the gentle use of a periosteal elevator and a ball-spiked pusher (illustrated), or a dental pick.
Skin incision for large pointed reduction forceps placement
Make a lateral skin incision for the insertion of a large pointed reduction forceps.
Temporary fixation with K-wire insertion
Hold the final reduction using a large pointed reduction forceps. Make sure not to place the pointed reduction forceps too posteriorly, as compression across the intercondylar notch would tend to tilt the fragment.
Secure the reduction with one, or more, temporary K-wires. Make sure that the K-wire does not conflict with the planned screw track.
Check of reduction Check the reduction in two planes using image intensifier control.
6. Lag screw insertion
In general, the screws are inserted at points along the midshaft axis of the femur (dotted line). The area distal to the Blumensaat’s intercondylar roof line must be avoided, in order not to violate the notch. In addition, the area of the medial knee recess should be avoided.
If you need to insert a screw in the area distal to the Blumensaat’s intercondylar roof line, direct the screw anteriorly, in order to avoid the intercondylar notch.
Drill screw hole
Make a small 1.2 cm incision.
Create a pilot hole using a 3.2 mm drill bit in the direction of the eventual screw insertion.
Determine appropriate screw length
Insert a depth gauge into the hole, to determine the appropriate screw length. Generally, a screw is chosen which is 5-10 mm short of the lateral cortex.
Remove the depth gauge and tap for the 6.5 mm cancellous bone screw under image intensifier control. In all but the densest cancellous bone of young athletes, tap only the near fragment – the screw itself will normally create its own thread in the cancellous bone of the far fragment
Insert the 6.5 mm partially threaded cancellous bone screw and fully tighten. In the case illustrated, the partially threaded screw will have 32 mm of thread, as opposed to 16 mm of thread.
Note: a washer may be used, particularly in osteoporotic patients.
Additional screw insertion
Insert 1 or 2 additional screws in a similar manner, and remove the K-wire.
7. Insertion of buttress plate
To enhance the stability and to avoid displacement of the fracture fragment by axial load (especially in osteoporotic bone), a buttress plate is needed.
Insertion of first screw
All types of 3.5mm plates can be used. A 5-hole standard 3.5 mm plate is sufficient. The plate must be contoured with a light prebend, that is, there should be a 1 mm gap between the central part of the plate and the bone.
Apply the buttress plate to the medial aspect of the distal femur. To press the plate firmly to the femur a standard cortical screw is inserted into the proximal hole, closest to the fracture. Perform drilling, screw length measurement and tapping, as usual.
Final screw insertion
Secure the buttress plate with two more bicortical cortical screws in the remaining proximal screw holes. Use standard bicortical cortical screws.
Check of implant position Check the osteosynthesis using the image intensifier in at least in two planes.
8. Wound closure
Irrigate all wounds copiously. Insert an intraarticular suction drain. Close the joint using absorbable sutures. The use of suction drains in the extraarticular tissues may be considered. Close the skin and subcutaneous tissue in the routine manner.
9. Aftercare following screw (and plate) fixation of partial articular fractures
Introduction Impediments to the restoration of full knee function after distal femoral fracture are fibrosis and adhesion of injured soft tissues around the metaphyseal fracture zone, joint capsular scarring, intra-articular adhesions and muscle weakness.
Continuous passive motion is a low load method of restoring movement and is a useful tool n the early post operative phase. It must be used in combination with muscle strengthening programs. With stable fracture fixation, the surgeon and the physical therapy staff will design an individual program of progressive rehabilitation for each patient.
The regimens suggested here are for guidance only and not to be regarded as proscriptive.
Functional treatment Unless there are other injuries, or complications, joint mobilization may be started immediately postoperatively. Both active and passive motion of the knee and hip can be initiated immediately postoperatively. Emphasis should be placed on quadriceps strengthening and straight leg raises. Static cycling without load, as well as firm passive range of motion exercises of the knee, allow the patient to regain optimal range of motion.
Weight bearing Touch-down weight bearing (10-15 kg) may be started immediately with crutches, or a walker. This will be continued for 6-8 weeks postoperatively. After that, touch-down weight bearing progresses to full weight bearing gradually over a period of the next 2 to 3 weeks. In general, patients are full weight bearing without devices (e.g., cane) by 10-12 weeks.
Follow up Wound healing should be assessed at 2 to 3 weeks postoperatively. Subsequently 6 week, 12 week, 6 month, and 12 month follow-ups are usually made. Serial x-rays allow the surgeon to assess the healing of the fracture.
Implant removal Implant removal is not essential, unless there are implant-related symptoms after consolidation.
Thrombo-embolic prophylaxis Consideration should be given to thrombo-embolic prophylaxis, according to local treatment guidelines.