As with any articular injury, anatomical restoration of the joint surface must be obtained. This is generally best done under direct vision, with clamp application, provisional fixation and then lag screw fixation.
The surgeon must bear in mind that the strong axial loading forces, as well as varus/valgus stress in the knee joint can tend to displace fragments. With vertical fracture lines, in particular, screw fixation alone may not be sufficient, and a buttress plate should be added.
Anatomy of the distal femur
The distal femur has a unique anatomical shape. Seen from an end-on view, the lateral surface has a 10° inclination from the vertical, while the medial surface has a 20–25° slope. A line drawn from the anterior aspect of the lateral femoral condyle to the anterior aspect of the medial femoral condyle (patellofemoral inclination) slopes approximately 10°. These anatomical details are important when inserting screws. In order to avoid joint penetration, screws should be inserted parallel to the patellofemoral and femorotibial joint planes.
2. Patient preparation
This procedure may be performed with the patient in one of the following positions:
The standard lateral/anterolateral approach gives satisfactory joint exposure to check the quality of the joint reduction.
4. Joint debridement
Remove the intraarticular hematoma and rinse the joint thoroughly with Ringer lactate solution.
Reduce the fragment using a periosteal elevator and a ball-spiked pusher (illustrated), or a dental pick.
Skin incision for pointed reduction forceps placement
Make a medial stab incision for the placement of the pointed reduction forceps.
Temporary fixation with K-wire insertion
Hold the final reduction using a large pointed reduction forceps. Make sure to place the pointed reduction forceps not too posterior as compression across the intercondylar notch would tend to tilt the fragment.
Secure the reduction with one, or more, temporary K-wires. Make sure that the K-wire does not conflict with the planned screw track.
Check of reduction
The quality of the reduction is confirmed radiographically.
6. Insertion of K-wires for cannulated screws
In general, the screws are inserted at points along the midshaft axis of the femur (dashed line). The area distal to the Blumensaat’s intercondylar roof line must be avoided in order not to violate the notch. In addition, the area of the lateral knee recess should be avoided.
If you need to insert a screw in the area distal to the Blumensaat’s intercondylar roof line, make sure to direct the screw anteriorly, in order to avoid the intercondylar notch.
Insertion of guide-wires
Insert the appropriate guide-wires for 7.3 mm cannulated screws, or, alternatively, 4.5 mm cannulated screws. Depending on the size of the fragment, 2 to 4 screws are necessary.
Guide-wire position check
Use the image intensifier to make sure that the tips of the guide wires just penetrate the far cortex.
In good bone stock, you may now remove the pointed reduction forceps. Otherwise, leave the pointed reduction forceps in place until all screws have been inserted.
Pitfall: too long a guide wire
It is important to remember that the distal femur tapers from the posterior to the anterior. Therefore, if a straight AP view is obtained, the guide wire can appear to be inside the bone. If it appears to be outside the bone, it is most likely too long. In order to assess the exact length of the guide wire obtain an AP view with 30° internal rotation of the lower extremity.
In this illustration, internal rotation by 30° reveals that the guide wire length was chosen inappropriately.
7. Cannulated screw insertion
Screw length determination
Determine the appropriate screw lengths using the dedicated measuring device.
Predrilling is usually not necessary.
If it is planned to use a plate it is helpful to slightly countersink the head of the most proximal screw. Manually insert the screws of appropriate length over the guide-wire.
Washers are helpful if plate application is not planned, and always in osteoporotic bone.
The temporary K-wire can now be removed.
Pearl: use temporary K-wire for further screw insertion
If you have used an appropriate K-wire size for temporary fixation of the fracture, you can now insert an additional cancellous screw further to enhance stability.
8. Wound closure
Irrigate all wounds copiously. Insert an intraarticular suction drain. Close the joint and the iliotibial tract using absorbable sutures. Close the skin and subcutaneous tissue in the routine manner.
Pearl: post-ORIF examination of knee joint stability under anesthesia With the femur now stable, it is possible to perform a gentle examination of the knee joint to exclude associated ligamentous laxity, but be extremely careful testing with valgus stress.
9. Aftercare following screw (and plate) fixation of partial articular fractures
Introduction Impediments to the restoration of full knee function after distal femoral fracture are fibrosis and adhesion of injured soft tissues around the metaphyseal fracture zone, joint capsular scarring, intra-articular adhesions and muscle weakness.
Continuous passive motion is a low load method of restoring movement and is a useful tool n the early post operative phase. It must be used in combination with muscle strengthening programs. With stable fracture fixation, the surgeon and the physical therapy staff will design an individual program of progressive rehabilitation for each patient.
The regimens suggested here are for guidance only and not to be regarded as proscriptive.
Functional treatment Unless there are other injuries, or complications, joint mobilization may be started immediately postoperatively. Both active and passive motion of the knee and hip can be initiated immediately postoperatively. Emphasis should be placed on quadriceps strengthening and straight leg raises. Static cycling without load, as well as firm passive range of motion exercises of the knee, allow the patient to regain optimal range of motion.
Weight bearing Touch-down weight bearing (10-15 kg) may be started immediately with crutches, or a walker. This will be continued for 6-8 weeks postoperatively. After that, touch-down weight bearing progresses to full weight bearing gradually over a period of the next 2 to 3 weeks. In general, patients are full weight bearing without devices (e.g., cane) by 10-12 weeks.
Follow up Wound healing should be assessed at 2 to 3 weeks postoperatively. Subsequently 6 week, 12 week, 6 month, and 12 month follow-ups are usually made. Serial x-rays allow the surgeon to assess the healing of the fracture.
Implant removal Implant removal is not essential, unless there are implant-related symptoms after consolidation.
Thrombo-embolic prophylaxis Consideration should be given to thrombo-embolic prophylaxis, according to local treatment guidelines.